Intelligent and fast-operating hollow lines-manufacture,factory,supplier from China

Main featureIt is used for polishing single glass, to prevent to hurt workman from sharp glass edgeIt adopts type of ‘x’ to polish the up and down edge at the same timeEasy operating, simple and flexible Technical dataPower supply380V 50HzTotal power3kwDimension2000*1200*820mm

The type of LJCJ01 smart insulating glass gas filling machine is special equipment for inflatable hollow glass. The device uses microcomputers and imported sensor to form a closed loop control system, high degree of intelligent equipment, precise control, pneumatic adjustable concentration, high charging efficiency, the operation is simple.

Main featureCan effectively seal the desiccant，to keep dryManual filling desiccant into spacer frame RecyclableEasy operating, simple and flexible Technical data Power supply220V 50HzTotal power1kwDimension2490*400*2200mm

   Smart insulating glass gas filling machine is special equipment for inflatable hollow glass. The device uses microcomputers and imported sensor to form a closed loop control system, high degree of intelligent equipment, precise control, pneumatic adjustable concentration, high charging efficiency, the operation is simple.

Main featureSpacer frame transport Easy operating, simple and flexibleTechnical dataPower supply380V 50HzTotal power0.18kwDimension2520*3012*3000mm

Main featureIt is used for sharpening unmarried glass, to save you to harm workman from sharp glass aspectIt adopts kind of ‘x’ to shine the up and down aspect on the equal timeEasy operating, easy and flexible Technical dataPower supply380V 50HzTotal power3kwDimension2000*1200*820mm

• Can efficiently seal the desiccant，to hold dry• Manual filling desiccant into spacer frame• Recyclable• Easy operating, easy and flexiblePower supply220V 50HzTotal power1kwDimension2490*400*2200mm

We offer world-class array of SEMI-AUTO Aluminum Frame Transfer Machine that are treasured for high strength and durable standards. Our entire product range is quality tested on varied pre-determined parameters thereby delivering flawless product line.• Spacer frame transport• Easy operating, simple and flexiblePower supply380V 50HzTotal power0.18kwDimension2520*3012*3000mm

LJBZ2025G vertical hollow glass flat pressure production line can complete the following functions: glass cleaning, aluminum frame placement, ordinary double glass, ordinary three glass, double glass aeration and three glass aeration.LJBZ2025G is a special equipment in aluminum hollow glass production.

Main featureIt is used for sharpening unmarried glass, to save you to harm workman from sharp glass areaIt adopts kind of ‘x’ to shine the up and down area on the identical timeEasy operating, easy and flexible Technical dataPower supply380V 50HzTotal power3kwDimension2000*1200*820mm

• Can effectively seal the desiccant，to keep dry• Manual filling desiccant into spacer frame• Recyclable• Easy operating, simple and flexiblePower supply220V 50HzTotal power1kwDimension2490*400*2200mm

LJZW2020A Automatic Insulating Glass Aluminum Spacer Bar Bending MachineLIJIANG production line adopts the latest technology, its main purpose is to create high-end quality, provide customers with the latest production technology, improve production efficiency, save production costs and produce maximum benefits.Now LIJIANG mainly has two kinds of IG lines with different two different technologies. One uses transfer wheels to transport glass, and the other is a new technology that uses air-floating technology to transport glass.

Common problems and solutions in the production of insulating glassIn the production process of insulating glass, the frequently occurring problems are:1. When butyl rubber is extruded, burrs and not smooth 2. Butyl glue does not stick to aluminum strips and glass and loses its stickiness 3. After the second seal is completed, a cold flow of butyl rubber appears after some time 4. When butyl rubber is extruded, there will be glue breaking and blockage...Frequent problems in finished hollow glass products:1. Fogging inside the hollow glass 2. Condensation of hollow glass 3.

Main feature            Easy operating, easy and flexibleIt is used for solving and rotating glass whilst guide coating the outdoor of IG glassThe center sucker is appropriate for small portions of glass，however，greater guide body is for huge portions of glassTechnical dataPower supply380V 50HzTotal power0.37kwOperating dimension1500*1500mmDimension600*550*985mmWeight75/48kg

• PLC manage machine, contact display interface• Automatically discover the width of aluminum bar, the glue nuzzle may be automated adjust• The vital a part of the hydraulic machine the usage of German imports of additives to make certain that the plastic frivolously full• Fast preheat, enhance paintings efficiency Squeeze pressure10-18MPaTemperature 110~140℃ Aluminum spacer width6A - 27A Speed 5-47m/min Diameter of butyl cylinder200mm   Air supply0.4m³/minAir pressure≥0.6MPaTotal power  380V, 5.7KW,50HZDimension 2800×700×900mm(L×W×H）weight650k

1, Loading partTo Avoid the low-e Glass put inverse side and Leave wheel marks or scratch low-e Coating  We use coating inspection -metal film conductive (other company use Photoelectric detection, hard to recognize for higher transparent film coating)(Nylon and Polyurethane + metal column)2, Washing and Drying part* 3 pairs of soft brush can clean low-e glass and ordinary glass, soft hair diameter less than 0.1mm.* Stainless steel, rust proof.* The air knife is float design, and the appropriate distance between the glass surface and the air knife is always 3mm (Note :3mm is the best

Main feature            Easy operating, simple and flexibleIt is used for fixing and rotating glass when manual coating the outside of IG glassThe middle sucker is suitable for small pieces of glass，however，extra support frame is for large pieces of glassTechnical dataPower supply380V 50HzTotal power0.37kwOperating dimension1500*1500mmDimension600*550*985mmWeight75/48kg

• PLC control system, touch screen interface• Automatically identify the width of aluminum bar, the glue nuzzle can be automatic adjust• The critical part of the hydraulic system using German imports of components to ensure that the plastic evenly full• Fast preheat, improve work efficiency Squeeze pressure10-18MPaTemperature 110~140℃ Aluminum spacer width6A - 27A Speed 5-47m/min Diameter of butyl cylinder200mm   Air supply0.4m³/minAir pressure≥0.6MPaTotal power  380V, 5.7KW,50HZDimension 2800×700×900mm(L×W×H）weight650kg

Smart Vertical Edge Deleting Machine LJCM2545 Main feature• Two-way glass access• Delete double and triple silver low-e glass• Automatically measure glass size• Automatically distinguish low-e surface• Edge deletion is adjustable• The head can be rotated 360°• Safe and full automatic device• PLC control system, touch screen interface  • Six servos control system• Intelligent control system, can recognize batch processing Technical dataMax. glass processing size2500*4500mm Min. glass pr

Two-component glue coating machine is suitable for the last procedure of insulating glass production line, mainly used for two-component polysulfide glue, two-component silicone hollow glue coating.

1. UsageLJBZ2500PG Vertical insulating glass production line has the following functions: Washing glass, Installing aluminum frame, Pressing normal IG units, Pressing double IG units, Pressing double  three-layers IG units. LJBZ2500PG is a special equipment in the production of insulating glass with aluminum strip, which has so many advantages, such as small footprint, high efficiency, reliable performance, convenient maintenance and so on.

CNC automatic hollow glass aluminum spacer bending machineProduct description of automatic aluminum spacer bending machineAutomatic aluminum spacer bending machine LJZW2020Jinan Lijiang Glass automatic hollow glass aluminum spacer bending machine is a special equipment for the production of hollow glass aluminum frame, replacing the traditional manufacturing process.

APPLICATIONLijiang Production Line adopts the latest production technology, its main purpose is to create high-end quality, provide customers with the latest production technology and a complete set of product solutions, improve production efficiency, save production costs, and generate maximum benefits.At present, Lijiang hollow glass production line mainly adopts the new technology of air flotation to transport glass. This new technology is to prevent glass from being contaminated by wheels and leaving marks, so as to improve the quality of IG production. Detailed description1.

LJCJ02 type insulating glass gas filling machineHollow glass Gas Filling Machine LJCJ02 is a special equipment for hollow glass. The inflator is composed of microcomputer and imported sensor closed-loop control system. The equipment is highly intelligent, the control is accurate, the pneumatic concentration is adjustable, the working efficiency is high, the operation is simple.